Konica-minolta Polygon Editing Tool Bedienungsanleitung PDF herunterladen (Seite 8)

ConventionsforCommandReference(Chapter2)

Chapter2“CommandReference”(frompage21)givesanexplanationofthefunctionandoperatingprocedure

of each command in the menu order.

Theshortcutkeyandtheicon(displayedonthetoolbar)arealsoshowninthecommandtitle.

Werecommendthatyoumakeextensiveuseofshortcutkeyswhenrunningthissoftware.Notethatwhile

softwarekeysindicatedinthecommandreferenceareeffectivebydefault,youarefreetoaddnewshortcuts

andtocustomizetheexistingones.

Ref.

For information about using and customizing shortcut keys, see page 242.

14 9

Chapter

View

910

900

700

300

View – Zoom [Z] (Effective while held down)

Enlarging/Reducing the Displayed Item

This command is used to enlarge (zoom-in) or reduce (zoom-out) the displayed item, or to move the camera to

change the view angle.

Ref.

For a description of camera position, refer to the View – Camera Settings command (page 155).

Note

View – Zoom mode will be active when this command is selected. To cancel the View – Zoom mode, execute the View

– Zoom command again. However, if you are executing this command using the shortcut key, the View – Zoom mode

can be canceled by releasing the key.

Left : zoom-in, zoom-out

Middle ([Shift] + Left) : –

Right : Drags the camera.

Operating Procedure

Click [Zoom] on the [View] menu.

Drag the item in an element window

while holding down the left mouse button.

Dragging the item upward will enlarge it

(zoom-in) and dragging it downward will re-

duce it (zoom-out).

• To move the camera (i.e. drag the camera), drag

while holding down the right mouse button.

emo

The element will be displayed in simple form during

zoom and drag. It will be displayed in detailed form when

zooming or dragging is canceled.

Chapter

File

900

910

File – Import – Digitizer – Step Scan (When VIVID 900/910 is Selected)

Performing Step Scan with the VIVID 910 or VIVID 900

This command is used to take two or more shots using the rotating stage via the remote control function of this

software. If a rotating stage has been selected by the Turntable, rotation of the stage can also be controlled.

After the necessary shots are taken, scan the calibration chart required for calibration of rotation. Data ac-

quired from different angles will be subjected to registration, and the resulting data will appear.

Warning

Never stare into the laser emitting window.

Do not place a lens, mirror or optical element in the passage of the laser beam. Doing so may converge the

laser beam, resulting in damage to your eyes, burns or ﬁ re. To prevent the above accidents, make sure that a

wall or similar which can block the laser beam is located behind the object.

■ When Using Only the Rotating Stage

Operating Procedure

From the [File] menu, select [Import],

[Digitizer] and then [Step Scan].

The [File-Import-Digitizer-Step Scan] dialog

box will appear.

emo

• The calibration chart is an accessory of the rotating

stage set.

• Before performing the procedure below, make sure that

the digitizer you are going to use is selected by the File

– Select Digitizer command.

• If you have connected multiple VIVID 900/910 units,

you can select the unit to be used by changing the SCSI

ID. Note that the software can only load memory-card

data from the VIVID unit with the highest SCSI ID.

Note

If the rotating stage does not operate correctly from the

dialog box, turn OFF the stage, turn it ON again, and

then try to operate it.

Ref.

For details of the File – Select Digitizer command,

refer to page 144.

• The monochrome monitor image currently cap-

tured by the VIVID 900/910 will appear in the

Image area of the dialog box.

Place the object on the rotating stage.

To display the object in the middle of

the window, change the position of the

object or move the VIVID 900/910 back

and forth to change the view angle.

emo

If necessary, replace the lens attached to the VIVID

900/910.

Mouse

functions

Command name

Description of the command

Shortcut key

Command

icon

Chapter and

Nenu entry

In Chapter 2,

it shows the

model name.

The left column shows

detailed explanations of

each step.

The right column shows the

outline of the procedure.

* This sample page is for explanatory purposes.

Actual pages will be different.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 269 270

Konica-minolta Polygon Editing Tool Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Konica-minolta Polygon Editing Tool Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Konica-minolta Polygon Editing Tool